CDE Technology BV Led Spot MR16 10W Cold White

Posted by Marcel van der Steen in Led lights, Light measurements No Comments»

cde_mr16_10w30deg presents a led spotlight with some power. With its 10 W a lot of light is generated.

This article shows the measurement results. Many parameters are also found in the Eulumdat file.

See this overview for a comparison with other light bulbs.

Summary measurement data

parameter meas. result remark
Color temperature 5807 K Cold white
Luminous intensity Iv 308 Cd
Beam angle 66 deg
Power P 10.1 W
Power Factor 0.64 For every 1 kWh net power consumed, there has been 1.2 kVAhr for reactive power.
Luminous flux 333 Lm
Luminous efficacy 33 Lm/W
CRI_Ra 78 Color Rendering Index.
Coordinates chromaticity diagram x=0.3258 and y=0.3394
Fitting 230V It uses a current driver for the leds, converting 230 V mains into current.
PAR-value 2.9 μMol/s/m2 The number of photons seen by an average plant when it is lit by the light of this light bulb. Value valid at 1 m distance from light bulb.
S/P ratio 2.0 This factor indicates the amount of times more efficient the light of this light bulb is perceived under scotopic circumstances (ow environmental light level).
D  x H external dimensions 50 x 72 mm External dimensions of the light bulb.
D luminous area 46 mm Dimensions of the luminous area (used in Eulumdat file). This is equal to the ID of the reflector end at the front of the light bulb.
General remarks The ambient temperature during the whole set of measurements was 23.5-25 deg C.

Warm up effect: during the warm up time the illuminance decreased with 9 % and the consumed power decreased with 4 %.

Voltage dependency: the power consumption and illuminance do not vary when the voltage is varied from 200 – 250 V.

The dim-function of the current driver is tested. The three pre-sets seem to work well.

This article contains some additional photos at the end.

Measurement report (PDF) olino-pdf
Eulumdat file olino_eulumdat Right click on icon and save the file.

Overview table

cde_mr16_10w30degcw_summary2

The overview table is explained on the OliNo website. Please note that this overview table makes use of calculations, use this data with care as explained on the OliNo site.

Eulumdat light diagram

This light diagram below comes from the program Qlumedit, that extracts these diagrams from an Eulumdat file. It is explained on the OliNo site.

cde_mr16_10w30degcw_light_diagram

The light diagram giving the radiation pattern.

It indicates the luminous intensity around the light bulb. This light bulb has the same light diagram for the C0-C180 as for the C90-C270 plane since it has symmetry over is height axis.

Illuminance Ev at 1 m distance, or luminous intensity Iv

Herewith the plot of the averaged luminous intensity Iv as a function of the inclination angle with the light bulb.

cde_mr16_10w30degcw_pp_avg

The radiation pattern of the light bulb.

This radiation pattern is the average of the light output of the light diagram given earlier. Also, in this graph the luminous intensity is given in Cd.

These averaged values are used (later) to compute the lumen output.

cde_mr16_10w30degcw_ev_dep_kantelhoek

Intensity data of every measured turn angle at each inclination angle.

This plot shows per inclination angle the intensity measurement results for each turn angle at that inclination angle. There normally are differences in illuminance values for different turn angles. However for further calculations the averaged values will be used.

When using the average values per inclination angle, the beam angle can be computed, being 66 degrees. This is the average value but as the light bulb has a symmetry over its height axis, this angle is valid for all turn-angles the light bulb is looked at.

Luminous flux

With the averaged illuminance data at 1 m distance, taken from the graph showing the averaged radiation pattern, it is possible to compute the luminous flux.

The result of this computation for this light spot is a luminous flux of 333 Lm.

Luminous efficacy

The luminous flux being 333 Lm, and the power of the light bulb being 10.1 W, yields a luminous efficacy of 33 Lm/W.

A power factor of 0.64 means that for every 1 kWh net power consumed, a reactive component of 1.2 kVAr was needed.

Light bulb voltage (used on power supply!) 230 VAC
Light bulb current 69 mA
Power P 10.1 W
Apparent power S 15.8 VA
Power factor 0.64

Of this light bulb the voltage across ad the resulting current through it+its constant current driver power supply are measured and graphed. See the OliNo site how this is obtained.

cde_mr16_10w30degcw_u_i_waveforms

Voltage across and current through the lightbulb

The current does not have a sinusiodal form. It contains some peaks instead. The phase is about the same as the voltage. All together the powerfactor is relatively low with less than 0.7.

Also the power spectrum of the current is determined.

cde_mr16_10w30degcw_powerspectrumi_percent

Current power spectrum in % of the first harmonic (50 Hz).

The peaks in the current result in the appearance of the higher harmonics.

Color temperature and Spectral power distribution

cde_mr16_10w30degcw_powerspectrum_at_1m_distance

The spectral power distribution of this light bulb, energies on y-axis valid at 1 m distance.

The measured color temperature is about 5800 K which is cold white.

This color temperature is measured straight underneath the light bulb. Below a graph showing the color temperature for different inclination angles.

cde_mr16_10w30degcw_cct_function_of_incl

Color temperature as a function of inclination angle.

The measurement of CCT has been stopped when less than 5 lux (low illumination value) was measured or when the inclination angle was 90 degrees. With this lamp at 77.5 degree inclination angle less than 5 lux was measured (at the specific measurement distance).

The maximum beam angle is 66 degrees, meaning at an inclination angle of 33 degrees there is 50 % left of the initial illuminance value at 0 degrees. Most of the light energy is within this area. In this area the color temperature stays within 2 % of its value at 0 degrees inclination angle.

PAR value and PAR spectrum

To make a statement how well the light of this light bulb is for growing plants, the PAR-area needs to be determined. See the OliNo website how this all is determined and the explanation of the graph.

cde_mr16_10w30degcw_par_spectra_at_1m_distance

The photon spectrum, then the sensitivity curve and as result the final PAR spectrum of the light of this light bulb

The PAR number for this light results in 2.9 μMol/s/m2. This value is valid at 1 m distance from the light bulb and valid roughly inside its beam angle.

The PAR efficiency is 63 % (valid for the PAR wave length range of 400 – 725 nm). So maximally 63 % of the total of photons in the light is effectively used by the average plant (since the plant might not take 100 % of the photons at the frequency where its relative sensitivity is 100 %).

S/P ratio

The S/P ratio and measurement is explained on the OliNo website. Here the results are given.

cde_mr16_10w30degcw_s_and_p_spectra_at_1m_distance
The power spectrum, sensitivity curves and resulting scotopic and photopic spectra (spectra energy content defined at 1 m distance).

The S/P ratio is 2.0.

More info will come in a separate article.

Chromaticity diagram

cde_mr16_10w30degcw_chromaticity

The chromaticity space and the position of the lamp’s color coordinates in it.

The light coming from this lamp is close to the Planckian Locus (the black path in the graph).

Its coordinates are x=0.3258 and y=0.3394.

Color Rendering Index (CRI) or also Ra

Herewith the image showing the CRI as well as how well different colors are represented (rendered). The higher the number, the better the resemblance with the color when a black body radiator would have been used (the sun, or an incandescent lamp).

Each color has an index Rx, and the first 8 indexes (R1 .. R8) are averaged to compute the Ra which is equivalent to the CRI.

cde_mr16_10w30degcw_cri

CRI of the light of this lightbulb.

The value of 78 is (a bit) lower than 80 which is considered a minimum value for indoor usage.

Note: the chromaticity difference is 0.001 indicates the distance to the Planckian Locus. Its value is lower than 0.0054, which means that the calculated CRI result is meaningful.

Voltage dependency

The dependency of a number of lamp parameters on the lamp voltage is determined. For this, the lamp voltage has been varied and its effect on the following light bulb parameters measured: illuminance E_v [lx], the lamppower P [W], the (Correlated) Color Temperature [K] and the luminous efficacy [Lm/W].

cde_mr16_10w30degcw_voltagedependency

Lamp voltage dependencies of certain light bulb parameters, where the value at 230 V is taken as 100 %.

The consumed power varies < 2 % and the illuminane doesn’t vary when the voltage varies between 200-250 V. This variation is insignificant.

When the voltage at 230 V varies with + and – 5 V, then the illuminance varies within 0.1 %, so when abrupt voltage changes occur this effect is not visible in the illuminance output.

Warm up effects

After switch on of a cold lamp, the effect of heating up of the lamp is measured on illuminance E_v [lx], color temperature CT or correlated color temperature CCT [K], the lamppower P [W] and the luminous efficacy [lm/W].

cde_mr16_10w30degcw_startupeffect

cde_mr16_10w30degcw_startupeffect_end

Effect of warming up on different light bulb parameters. At top the 100 % level is put at begin, and at bottom at the end.

The warm-up time is about 25 minutes.

During this time the illuminance value and the consumed power decrease with 9 % and 4 % respectively.

The small variations in illuminance at the end of the measurement time come from the variations in ambient temperature (23.5 – 25 ºC).

Dim-functionality

The used current source enables dimming the connected light bulbs by switching off and on within 2 seconds. The dim-presets are 100 %, 33 % and 66 %.
cde_mr16_10w30degcw_to_less_intensity

Lamp parameters dependent on the dim-position

The consumed power and the illuminance values are nicely linear with the dim-presets; the illuminance follows the specified 33 %, 67 % and 100 % levels.

The consumed power decreases only marginally slower than the illuminance does.

The color temperature decreases slightly when dimming takes place.

Additional photos

cde_mr16_10w30deg_close_up
Close up of the LED inside the lamp reflector

cde_mr16_10w30deg_side_view
Side view of the light bulb


cde_mr16_10w30deg_psu_dimmer
The used current driver

This is a very versatile current driver: the constant current can be set with dip-switches. During this lamp measurement it was set to 800 mA. Then it can be connected to a (remote) dimmer. It also enables dimming with three presets when switching off and on within 2 seconds, as explained before and which is tested in this article.

Leave a Reply

Your email address will not be published. Required fields are marked *