presents a 150 cm long LED tube light. The cover used is frosted, and was especially selected after a field test where a lot of people could give their preference. The color of the light is warm white. Of the same model a cold white and neutral white version are available.

This article shows the measurement results. Many parameters are also found in the Eulumdat file.

See this overview for a comparison with other light bulbs.

Summary measurement data

parameter	meas. result	remark
Color temperature	3145 K	warm white
Luminous intensity Iv	268 Cd	Measured straight underneath the lamp
Beam angle	138 deg	138º for the C0-C180 plane (crosses the length direction of tube), and 110º for C90-C270 plane (length direction of the tube).
Power P	19.0 W
Power Factor	0.90	For every 1 kWh net power consumed, there has been 0.5 kVAhr for reactive power.
Luminous flux	1036 Lm
Luminous efficacy	55 Lm/W
CRI_Ra	65	Color Rendering Index.
Coordinates chromaticity diagram	x=0.4369 and y=0.4217
Fitting	FL-tube	It is connected directly to the grid.
PAR-value	2.2 μMol/s/m2	The number of photons seen by an average plant when it is lit by the light of this light bulb. Value valid at 1 m distance from light bulb.
S/P ratio	1.1	This factor indicates the amount of times more efficient the light of this light bulb is perceived under scotopic circumstances (ow environmental light level).
D x L external dimensions	29 x 1500 mm	External dimensions of the lamp. Excluding the pins.
L x W luminous area	1474 x 29 mm	Dimensions of the luminous area (used in Eulumdat file). This is equal to the surface of the frosted cover.
General remarks		The ambient temperature during the whole set of measurements was 24 deg C. Warm up effect: during the warm up time the illuminance decreases with ≈20 % and the consumed power with ≈17 %. Voltage dependency: the power consumption and illuminance do depend a little on the voltage when it is varied from 200 – 250 V.
Measurement report (PDF)
Eulumdat file		Right click on icon and save the file.

Overview table

The overview table is explained on the OliNo website. Please note that this overview table makes use of calculations, use this data with care as explained on the OliNo site.

Eulumdat light diagram

This light diagram below comes from the program Qlumedit, that extracts these diagrams from an Eulumdat file. It is explained on the OliNo site.

The light diagram giving the radiation pattern.

It indicates the luminous intensity around the light bulb. In the length direction (C90-C270) the beam angle is somewhat smaller than perpendicular on it (C0-C180).

Illuminance Ev at 1 m distance, or luminous intensity Iv

Herewith the plot of the averaged luminous intensity Iv as a function of the inclination angle with the light bulb.

The radiation pattern of the light bulb.

This radiation pattern is the average of the light output of the light diagram given earlier. Also, in this graph the luminous intensity is given in Cd.

These averaged values are used (later) to compute the lumen output.

Intensity data of every measured turn angle at each inclination angle.

This plot shows per inclination angle the intensity measurement results for each turn angle at that inclination angle. There normally are differences in illuminance values for different turn angles. However for further calculations the averaged values will be used.

When using the average values per inclination angle, the beam angle can be computed, being 110º for C90-C270 plane (length direction) and 138º for the C0-C180 plane (crossing the length direction).

Luminous flux

With the averaged illuminance data at 1 m distance, taken from the graph showing the averaged radiation pattern, it is possible to compute the luminous flux.

The result of this computation for this light spot is a luminous flux of 1036 Lm.

Luminous efficacy

The luminous flux being 1036 Lm, and the power of the light bulb being 19.0 W, yields a luminous efficacy of 55 Lm/W.

A power factor of 0.90 means that for every 1 kWh net power consumed, a reactive component of 0.5 kVAr was needed.

Light bulb voltage (used on power supply!)	230 VAC
Light bulb current	92
Power P	19.0 W
Apparent power S	21.1 VA
Power factor	0.90

Of this light bulb the voltage across ad the resulting current through it+its constant current driver power supply are measured and graphed. See the OliNo site how this is obtained.

Voltage across and current through the lightbulb

The current does not look like a sine, but it tries to approach it. There are peaks (steep edges) in the current form, which will lead to higher harmonics. The current phase is leading a little bit the voltage. The result is a nice powerfactor of around 0.9.

Also the power spectrum of the current is determined.

Current power spectrum in % of the first harmonic (50 Hz).

Due to the steep edges in the current there are some higher harmonics in the current spectrum.

Color temperature and Spectral power distribution

The spectral power distribution of this light bulb, energies on y-axis valid at 1 m distance.

The measured color temperature is about 3150 K which is warm white.

This color temperature is measured straight underneath the light bulb. Below a graph showing the color temperature for different inclination angles.

Color temperature as a function of inclination angle.

The measurement of CCT has been stopped when the inclination angle was 65 as the illuminance value was decreased to very low values there (< 5 lux).

The beam angle is 138º, meaning an inclination angle of max 69º. Almost all light falls within this angle. The variation of the color temperature within this angle is about 1 %.

PAR value and PAR spectrum

To make a statement how well the light of this light bulb is for growing plants, the PAR-area needs to be determined. See the OliNo website how this all is determined and the explanation of the graph.

The photon spectrum, then the sensitivity curve and as result the final PAR spectrum of the light of this light bulb

The PAR number for this light results in 2.2 μMol/s/m². This value is valid at 1 m distance from the light bulb and valid roughly inside its beam angle.

The PAR efficiency is 62 % (valid for the PAR wave length range of 400 – 725 nm). So maximally 62 % of the total of photons in the light is effectively used by the average plant (since the plant might not take 100 % of the photons at the frequency where its relative sensitivity is 100 %).

S/P ratio

The S/P ratio and measurement is explained on the OliNo website. Here the results are given.

The power spectrum, sensitivity curves and resulting scotopic and photopic spectra (spectra energy content defined at 1 m distance).

The S/P ratio is 1.1.

More info will come in a separate article.

Chromaticity diagram

The chromaticity space and the position of the lamp’s color coordinates in it.

The light coming from this lamp is at a distance from the Planckian Locus (the black path in the graph).

Its coordinates are x=0.4369 and y=0.4217.

Color Rendering Index (CRI) or also Ra

Herewith the image showing the CRI as well as how well different colors are represented (rendered). The higher the number, the better the resemblance with the color when a black body radiator would have been used (the sun, or an incandescent lamp).

Each color has an index Rx, and the first 8 indexes (R1 .. R8) are averaged to compute the Ra which is equivalent to the CRI.

CRI of the light of this lightbulb.

The value of 65 is smaller than 80 which is considered a minimum value for indoor usage.

Note: the chromaticity difference is 0.0069 indicates the distance to the Planckian Locus. Its value is higher than 0.0054, which means that the calculated CRI result is not meaningful.

Voltage dependency

The dependency of a number of lamp parameters on the lamp voltage is determined. For this, the lamp voltage has been varied and its effect on the following light bulb parameters measured: illuminance E_v [lx], the lamppower P [W], the (Correlated) Color Temperature [K] and the luminous efficacy [Lm/W].

Lamp voltage dependencies of certain light bulb parameters, where the value at 230 V is taken as 100 %.

The illuminance and consumed power vary a bit when the voltage is varied.

When the voltage at 230 V varies with + and – 5 V, then the illuminance varies ≈ 1.0 %, so when abrupt voltage changes occur this effect is not visible in the illuminance output.

Warm up effects

After switch on of a cold lamp, the effect of heating up of the lamp is measured on illuminance E_v [lx], color temperature CT or correlated color temperature CCT [K], the lamppower P [W] and the luminous efficacy [lm/W].

Effect of warming up on different light bulb parameters. At top the 100 % level is put at begin, and at bottom at the end.

The warm up time is about 35 minutes. During that time the illuminance decreases with ≈20 % and the consumed power with ≈17 %.